William Nawky Snowmobile Auction

Carbides Snowmobile

Motorcycle and Atv Cylinder Rebuilding Options

Recent History of Cylinder Types

The oldest and most common method of cylinder design is a cast iron block that is machined with a cylindrical bore directly from a solid casting. There is also a cast iron block that incorporates a sleeve that is pressed into the iron block. Generally iron block motors weren’t very successful in small engines. Most small engines were used in vehicles and equipment that needed to be light and mobile. This made cast iron blocks undesirable for this purpose. There were a lot of single cylinder motors used in lawn mowers, construction equipment, scooters, small tractors and small motorcycles that used cast iron block motors in the early years. These began to disappear in the 60’s and they were replaced by aluminum block motors with cast-in iron liners. This opened the door for new lightweight motors that could be used in many more applications and in bigger displacements than ever before. This was accomplished by placing a cast iron sleeve into the mold before the molten aluminum was poured into the mold. This made the sleeve an integral part of the cylinder block. The sleeve usually had locking rings or flanges around the outside to prevent it from slipping in the casting as the engine expanded from the heat generated by the combustion process. A major problem occurred often when air pockets would develop during the casting operation around the sleeve. This caused hot spots and often caused premature engine cylinder failure.

There is another type of aluminum block with a cast iron sleeve that wasn’t cast-in; it is installed in the block after casting. The cylinder bore of the aluminum block is machined to 3-5 thousands of an inch less than the sleeve diameter, block is then heated to around 600 degrees Fahrenheit, and the sleeve is dropped in. When the block cools the sleeve is held in place by the interference fit and the flange at the top or bottom of the cylinder. This cylinder can be rebuilt by simply re-heating the block to 600 degrees and removing the old sleeve and replacing it with a new one. Of course the finish bore will have to be machined to size and honed.

Near the end of the last century it was discovered that you could make a mold pattern using a computer aided molding system out of Styrofoam. This made it possible to have precise duplicate patterns of a particular cylinder that you wanted to mold of aluminum.

These are placed in a mold made of sand, molten aluminum is then poured slowly into the mold melting and replacing the Styrofoam pattern. This process is called total loss mold casting. Now all they have to do is a little milling and drilling, plate the bore and hone to size. For the two stroke market the best part of this is the finished product is an identical copy of the original. The factories love this because it just eliminated a whole lot of assembly line workers. No more absenteeism, no health insurance or pensions, and no coffee breaks. As far as the consumer goes they get a cylinder that doesn’t need a lot porting before they can be competitive.

There are a lot of four stroke motors that use aluminum blocks and aluminum sleeves that are plated a variety of hard finishes. These sleeves can be removed and replaced. The replacement sleeve can be either iron or aluminum. If you want an aluminum sleeve it will have to be plated after installing otherwise it won’t be true and round.

There are several types of plating that has been used over the years, and the companies doing plating guard their formulas carefully. The finish in the early years was a simple chrome or hard chrome electro-plating. The plating was generally only a few thousands of an inch thick. If it was more than about ten thousands of an inch thick it was prone to chipping or flaking because of heat expansion and contraction. In the early seventies Electrofusion became popular. Electrofusion was different from electroplating in as much as it was a fusion process instead of electroplating. Next there was ceramic composites and Boron. All of these perform in about the same way as far as wear and durability. Then there was Nikasil. Nikasil was a new plating formula of nickel-silicon-carbide. It was harder than the others that came before it. For years you couldn’t get a cylinder re-plated when you damaged one, the only way to get going again was to buy a new one. Now you can choose from many companies doing their own version of Nikasil.

Now let’s look at a person’s choice of repair or rebuilding methods for their Motorcycle, ATV, Snowmobile, Personal Watercraft, or Outboard. You can have your Nikasil or other plated cylinder re-plated (or some called it re-coated). This includes the composite types.

Or you can have it sleeved with a hardened alloy steel or cast iron (when you add alloys to iron its considered steel). If your cylinder has an iron sleeve already, whether it’s cast-in or not, you’re only real choice is replacing it with another sleeve or a sleeve liner.

Let’s assume you’re an avid racer and race 25 weekends a year, you’re going to need a rebuild of your cylinder by the end of the year no matter what type cylinder you have. If it is a plated type cylinder you have three choices. 1- buy a new cylinder for $500-600 for the top end and expect to do the same next year. 2- re-plate it for about $300-400 with piston kit and gaskets and figure on doing it again next year. 3- have it sleeved for about $250-350 with piston kit and gaskets and next year have it bored (most models) to the next size for about $55 plus piston kit and gaskets.

A properly sleeved cylinder will perform as well as any plated cylinder. A properly sleeved cylinder is one that has the proper interference fit, proper pre-sleeve bore finish, accurate flange machining, and sleeve made from the proper alloys. The most popular sleeve is the Moly 2000 chrome-moly iron. The proper boring and honing to match the piston clearance requirements goes without saying.

Pros and Cons

Re-Plated Cylinder Bore

Pros

• Small advantage in heat transfer

• Slightly better wear factor

• Somewhat lower co-efficient of friction

• Weighs a few ounces less

Cons

• Costs slightly more

• Can’t be bored when damage occurs

• More fragile

• Can flake and peel

Iron Sleeved Cylinder Bore

Pros

• Costs less

• Boreable for future over sizes

• Honeable to keep bore true and proper ring seal

• Can be worked with common tools

• Can be replaced when needed

Cons

• Slightly slower heat transfer

The Bottom Line

Both systems perform equally well when professionally done, so it really comes down to economics. You can expect a sleeved cylinder to give more life for the money. Re-plated cylinders are as close to original as you can get. So if you’re happy with your OEM plated cylinder you should have it re-plated. If not have it sleeved by a company that has the reputation, experience, and warrantees to protect your investment. http://kustom-kraft.com

About the Author

Dominator 4-inch Carbides $85.2 Set includes one front and one rear carbide wearpad Snowmobile accessory is 4 inches of control carbideBar size: 0.4375 inches60-degree carbide in 1-inch segmentsProvides durability and maximum control

Dominator 6-inch Carbides $101.82 Set includes one front and one rear carbide wearpad Snowmobile gear is six (6) inches of control carbideBar size: 0.4375 inches60-degree carbide in 1-inch segmentsProvides durability and maximum control

Handbook of Refractory Carbides & Nitrides $205 Refractory carbides and nitrides are useful materials with numerous industrial applications and a promising future, in addition to being materials of great interest to the scientific community. Although most of their applications are recent, the refractory carbides and nitrides have been known for over one hundred years. The industrial importance of the refractory carbides and nitrides is growing rapidly, not only in the traditional and well-established applications based on the strength and refractory nature of these materials such as cutting tools and abrasives, but also in new and promising fields such as electronics and optoelectronics.

Jet Snowmobile $39.99 Jet Snowmobile - Giclee Print

Couple on a Snowmobile $24.99 Couple on a Snowmobile - Photographic Print

Teddies with Snowmobile $49.99 Teddies with Snowmobile - Giclee Print

Man on Snowmobile $24.99 Man on Snowmobile - Photographic Print

Cemented Tungsten Carbides $205 Written by an international expert, this book covers the processing, microstructure, and properties of cemented tungsten carbides. It is divided into 18 chapters covering wide areas from crystal structure to phase equilibria, production of metal and carbide powders, and much more. This book is ideal for researchers, plant engineers, and senior level students in metallurgical/mechanical/materials engineering who are interested in cemented carbides. There is no parallel book in print.

Maine, Snowmobile Scene $19.99 Maine, Snowmobile Scene - Premium Poster

A Person Riding a Snowmobile $19.99 A Person Riding a Snowmobile - Premium Poster

California, Snowmobile Scene $19.99 California, Snowmobile Scene - Premium Poster

Massachusetts, Snowmobile Scene $19.99 Massachusetts, Snowmobile Scene - Premium Poster

Oregon, Snowmobile Scene $19.99 Oregon, Snowmobile Scene - Premium Poster

Washington, Snowmobile Scene $19.99 Washington, Snowmobile Scene - Premium Poster

Jet-Propelled Snowmobile $34.99 Jet-Propelled Snowmobile - Giclee Print

Canada, Snowmobile Scene $19.99 Canada, Snowmobile Scene - Premium Poster

Vermont, Snowmobile Scene $19.99 Vermont, Snowmobile Scene - Premium Poster

Alaska, Snowmobile Scene $19.99 Alaska, Snowmobile Scene - Premium Poster

Arizona, Snowmobile Scene $19.99 Arizona, Snowmobile Scene - Premium Poster

Montana, Snowmobile Scene $19.99 Montana, Snowmobile Scene - Premium Poster

Utah, Snowmobile Scene $19.99 Utah, Snowmobile Scene - Premium Poster

Colorado, Snowmobile Scene $19.99 Colorado, Snowmobile Scene - Premium Poster

Connecticut, Snowmobile Scene $19.99 Connecticut, Snowmobile Scene - Premium Poster

Wyoming, Snowmobile Scene $19.99 Wyoming, Snowmobile Scene - Premium Poster

Idaho, Snowmobile Scene $19.99 Idaho, Snowmobile Scene - Premium Poster